3D Printing Stack Exchange
3D Printing Stack Exchange

Most Popular

more tags
1500 questions
8
votes
1 answer

Unidentified problem in printing

I have printed the XY resonance, Z resonance, bridging performance and the negative space tolerance test, from Makezine (can be found here), and I have encountered the following errors in the prints. Z resonance test: The layers are shifting as the…
Veda
  • 461
  • 2
  • 7
8
votes
1 answer

MINTEMP error after crash

I just got my HICTOP Prusa i3 Aluminium frame printer and finished putting it together. After setting it to preheat, I realized the bed was not level - I adjusted it and accidentally caused the head to crash into the bed. It sounded like something…
jmontineri
  • 121
  • 6
8
votes
3 answers

Missing top layers in Cura

I've just tried to make some small labels with embossed lettering. Base is 1.5 mm, with letters and a perimeter protruding by another 1 mm. After printing, I realised that Cura is not giving me a top layer, all I get is an inner and outer wall for…
Sean Houlihane
  • 3,852
  • 2
  • 22
  • 39
8
votes
6 answers

How to directly send G-code to printer from a Linux terminal?

Should it be possible to directly send G-code to the printer serial connection using pipes under Linux? Example: echo M106 > /dev/ttyUSB0 My controller runs at 250000 baud, I have tried setting the TTY baud rate to 250 kBd with: stty -F…
Mtl Dev
  • 639
  • 2
  • 8
  • 20
8
votes
1 answer

How much insulation do I really need?

I have been looking at cork sheet insulation for my 200 mm x 300 mm aluminium PCB heatbed, by I am not entirely sure how thick it should be. There seems to be a trade off between losing a few millimeters of print height, and providing adequate…
Greenonline
  • 6,748
  • 8
  • 40
  • 68
8
votes
1 answer

What makes a good PLA filament?

The quality of the filament is frequently mentioned either as the source of an issue but also as the solution to a problem. I know that the way you use,store and protect your filament will greatly impact it's quality, especially overtime, but here…
guillaume.molter
  • 155
  • 3
8
votes
3 answers

Weird bumps cylindrical hole

Not quite sure what's happening here. I printed it as a single ball and had this effect. I thought it might be a cooling issue so I printed 4 at once but the issue still occurred. If I size the ball up, the problem reduces. Note that the hole is…
easycheese
  • 427
  • 1
  • 3
  • 13
8
votes
1 answer

First (bottom) layer has gaps

First off - I'm rather new to this and I might be on the wrong track altogether... I'm printing PLA using a simple DIY XYZ printer with a direct-driven extruder, 0.3 mm nozzle, 0.2 mm layer heights, using Slic3r. I've tried to calibrate the bed as…
vwegert
  • 476
  • 5
  • 12
8
votes
3 answers

I am experiencing some severe under extrusion

I did calibrate the extruder to extrude exactly 50/100 mm and it is fine. I have replaced the old (prehistorical) extruder that was giving me the problem with a new one. The issue does not go away. It is severely under extruded. The nozzle is a 0.4…
FeliceM
  • 581
  • 7
  • 18
8
votes
4 answers

Does the printing substrate have to be glass? If so, what size?

I am new to 3D printing. I have just put together my own 3D printer with some help. I was advised I shouldn't print directly onto the aluminium plate - I assume it's aluminium. The manufacturer did give me a piece of matrix board (i.e. no cooper at…
Ageis
  • 699
  • 1
  • 8
  • 16
8
votes
3 answers

Why does print fall apart at beginning of top layer?

I'm looking for any idea of what could cause this problem. I'm printing (1.75 mm PLA @ 220 °C) a 14 x 14 cm box, sliced with Simplify3D. Relevant settings are 3 bottom layers, 3 top layers, 3 outline/perimeter shells, and 15 % orthogonal infill…
Fred Hamilton
  • 281
  • 2
  • 7
8
votes
3 answers

Connector Suggestion for Extruder and Heatbed

On my Reprap-like 3D printer, I routed all the wires to a spot near the base; for the motors, endstops, thermistors, etc, I plugged them all into a DB25 breakout board, and that's working great. For my Extruder (12v), and my heat bed (16v), I'm…
BrainSlugs83
  • 343
  • 3
  • 9
8
votes
1 answer

Take a detailed model and make it suitable for 3D printing?

I have a model I would like to print, specifically it is a free-for-personal-use model of a car, complete with interior. I would like to print it, but it is unprintable. I have tried to fix it in netfabb, which works OK. But now I realised I have…
James T
  • 296
  • 2
  • 11
8
votes
2 answers

M3D Micro printer stops extruding but is not clogged

I have an M3D Micro 3D printer that printed fine for a couple of weeks and then was plagued with issues afterward. I've done the fixes from the forum to get proper heating and cooling of the nozzle (I've added aluminum foil around the nozzle to make…
Airfield20
  • 459
  • 1
  • 3
  • 9
8
votes
5 answers

How do you heat a large glass print bed?

I have printed a MPCNC machine. It has a print area of about 30" x 30" and up to 11" tall. (yes, those numbers are correct). I found a perfect piece of glass at a garage sale for $5.00 to use as my print bed. My problem now is how to heat the…
Curtis
  • 385
  • 1
  • 3
  • 10
1 2 3
…
99 100